Tennant S30 Squeegee Blade: Fitment, Grades and MOQ

S30/M30 squeegee rubber blades

Table of Contents

Aftermarket replacement part — not a genuine OEM part. The squeegee blades and rubber parts on this page are aftermarket replacements made to fit Tennant machines. They are not genuine Tennant parts, we are not affiliated with or endorsed by Tennant, and brand names, model names and part numbers are used for fitment reference only. Confirm dimensions against your own sample or drawing before ordering.

If you distribute squeegee blades, the Tennant S30 is rarely a single-machine problem. It turns up inside a fleet alongside other units, and the real question is not whether you can source a blade for it, but how many different blades you must hold to cover the fleet without burying working capital in slow-moving stock. Fitment work for a distributor is inventory work: group the fleet by blade profile rather than by model name, and the SKU count usually drops by a third.

This page covers how to tell whether the S30 assembly matches a profile you already stock, how many rubber grades are worth carrying, and the order terms for testing a style without committing to a full container.

Fitment is three variables, not a model number

A model name tells you which machine family an assembly belongs to. It does not tell you what blade fits. Three independent variables do, and only the first one is usually checked:

Variable What to compare What goes wrong
Cross-section Slot width, blade thickness, lip profile A blade that seats but rocks in the channel never seals
Length and cut Overall length, end treatment A few millimetres short leaves water at both corners
Mounting Hole or slot pitch, clamp type Wrong pitch means the blade cannot be tensioned evenly

Cross-section and mounting are the two that decide whether a blade works at all. Length is the one that decides whether it works quietly. Most fitment failures reported to us turn out to be a cross-section mismatch rather than a length problem: the blade goes into the frame, looks correct, and then leaves a thin trail down the middle of the cleaning path because the lip is sitting at the wrong angle.

For exact slot dimensions, thickness, hole pitch and length on your S30 build, we work from a sample or a drawing rather than a generic chart. Frames are revised between production runs and differ between regions, so anything we cannot confirm we say so instead of guessing. Send the worn blade or a clear photo of the frame and we will confirm before shipping or before cutting tooling.

Where consolidation actually works

The saving from consolidation comes from a pattern that surprises most first-time buyers: assemblies are shared across machine families far more often than the model names suggest. A supplier who stocks one blade per model number will hold far more stock than the fleet actually needs.

Group your machines by profile and mounting instead, and three things follow:

  1. One blade serves several units. Where two machines in the fleet share a squeegee frame, they share a blade, and that is one SKU instead of two.
  2. Revisions break the grouping, not the model. A frame replaced or revised in service is a new profile. It counts as its own line, whatever the machine badge says.
  3. The long tail stays small. Odd machines that turn up once a year are better handled as an order-on-request line than as stock you finance all year.

Our cross-reference guide lists the models and brands we already hold tooling for. Treat it as a starting list for grouping, not as a dimensional chart: confirm the profile against your own sample or drawing before you place the order. Where an assembly has been changed in service, send the worn blade and let us match it rather than assume the catalogue entry still applies.

How many grades to carry

Carrying all three grades for every profile triples the inventory for no gain. Most distributors settle on a simpler rule: stock the grade that covers the bulk of the fleet, and treat the others as order-on-request unless you have named accounts that justify holding them.

Hardness belongs on the order as a range with a tolerance and a named test method. Durometer is measured by the ASTM D2240 test method; ask for readings off production pieces, not a compounder’s test coupon. Our three grades carry a ±5 Shore A tolerance:

  • Natural rubber, 65 ± 5 Shore A — smooth tile, PVC and epoxy. Conforms well to flat floors and gives the cleanest pickup. This is the default for most indoor commercial work and the one to stock, unless your accounts tell you otherwise.
  • Cast polyurethane, 85 ± 5 Shore A — rough or damaged concrete, expansion joints, oily and greasy surfaces, and long shifts over abrasive floors. Worth holding if you serve warehouses, workshops or loading areas.
  • Economy gum rubber, 45 ± 5 Shore A — light duty on smooth floors where the decision is price-led and the area is small.

The full trade-off, including where each grade stops making sense, is set out in our material comparison. Two assumptions cost distributors money. The first is that harder is always better: on polished tile a hard blade chatters and streaks, and more down-pressure makes it worse. The second is that red means premium — red is pigment, performance is formulation, which is why our red rubber sheet guide treats colour separately from specification.

Polyurethane generally lasts longest on rough or oily floors, but it is more sensitive to temperature and operating conditions than natural rubber. Sell it with that caveat attached rather than as a flat upgrade. A site that is cold at opening and warm by midday is exactly where that caveat matters.

Service life sets the reorder point

Service life in normal commercial duty is typically two to three months, an industry figure rather than a guarantee. It moves with cleaning frequency, chemicals, temperature and floor condition. For a distributor it matters less as a promise to end users than as a planning input: how often the same accounts reorder, and how much safety stock each profile needs. Our replacement cycle guide covers how to turn that interval into a reorder point from the number of units your customers run.

There is a safety argument as well. A squeegee that no longer seals leaves water on the walking surface, and slip hazards on wet floors fall under workplace rules such as OSHA 1910.22 in the United States. Blades are a small line item; the cost of a re-clean, a complaint or an incident is not. Consolidating styles into fewer, larger orders is also standard practice in the cleaning channel, and ISSA material is a useful reference when making that case internally.

Order terms for a mixed first order

A distributor testing a new profile should not have to fill a container with it. The terms are built for that:

  • MOQ 20 sets per style on a profile we already tool. One set is one front blade plus one rear blade — order “blades” and you may be quoted single strips.
  • USD 60–120 tooling for a profile we do not hold, waived once cumulative volume reaches 500 sets.
  • Mixed orders allowed, with a USD 3,000 minimum order value, so one shipment can cover a dozen models instead of committing the whole budget to one.
  • Samples are chargeable, not free, and take 7–15 days to prepare and ship.

Cumulative volume counts across reorders, so a stable profile moves you toward the tooling threshold instead of restarting it. Ask for carton labelling by style and by half of the set: goods-in cannot sort an unlabelled mixed pallet.

Claims are agreed on the order, not after it: raised within 7 days of receipt, counted from the delivery date rather than dispatch; only the defective pieces replaced, not the whole batch; an unboxing video filmed from before the carton opens; and freight on replacement pieces on the buyer, which most importers absorb by consolidating into the next shipment. Coverage is for manufacturing defects — damaged or feathered edges, wrong dimensions, defective material, hardness outside the agreed range — not ordinary wear, fitting damage, or early wear from specifying the wrong compound for the floor.

Margin on this line usually sits in the gap against a captive OEM parts channel rather than in shaving unit price, an argument developed in OEM vs aftermarket squeegee blades.

Get a quote or a sample set

Send us the machine models in the fleet, how many units your customers run, the floor types, and whether the assemblies are straight or curved. We will confirm the S30 profile against a sample or drawing, tell you which of your existing lines it can be grouped with, and recommend a grade for your conditions. Request pricing or a sample set and we will come back with lead time, freight options, and a 20-set trial you can fit before committing to volume.

Facebook
LinkedIn
Twitter

Leave a Reply

Your email address will not be published. Required fields are marked *

9 − four =

Sign up and get

5% Off

On all squeegee blade

Ask For A Quick Quote

We will contact you within 1 working day, please pay attention to the email with the suffix “@ntheron.com”.