Choosing Rubber for a Tennant T5680 Squeegee Blade

Tennant 5680 squeegee blades

Table of Contents

Aftermarket replacement part — not a genuine OEM part. The squeegee blades and rubber parts on this page are aftermarket replacements made to fit Tennant machines. They are not genuine Tennant parts, we are not affiliated with or endorsed by Tennant, and brand names, model names and part numbers are used for fitment reference only. Confirm dimensions against your own sample or drawing before ordering.

The grade that is right for a Tennant T5680 working a heated retail aisle in July is often the wrong grade for the same machine in an unheated loading bay in January. Nothing about the machine changed. What changed is the exposure window the rubber has to survive. Choosing rubber is therefore less a contest over hardness numbers than a decision about temperature, cleaning chemistry and how quickly a wet floor gets noticed. This page sets out that decision, the three compounds we supply, the dimensions we will not guess at, and the wholesale terms behind a trial order.

The machine fixes the profile; the site fixes the compound

A model name identifies a machine family. It does not define slot width, lip geometry, thickness, hole pitch or overall length, and we do not publish dimensions, OEM part numbers or abrasion test values that we cannot confirm from your sample or drawing. A plausible-looking figure that seats the lip at the wrong angle leaves a trail and is then reported as a bad batch of rubber. Where a dimension is missing, confirm it with us against your own sample or drawing rather than filling the gap with a catalogue figure.

The Tennant official site is the right place to start for machine documentation, though it will not tell you which aftermarket profile fits a frame that has been revised or replaced in service. Our cross-reference guide lists the profiles we already hold tooling for; treat it as a starting list, then confirm against the worn blade.

One distinction belongs at the top of every enquiry: one set is one front blade plus one rear blade. On a wide rider the rear carries the vacuum seal across the width, while the front takes the debris and most of the abrasion. Quote requests that say only “T5680 blades” are routinely priced as single strips, so state the split. A frame replaced with a non-original assembly, an earlier production run with a revised frame, or a set trimmed and re-drilled on site each count as a new profile, whatever the badge says.

Three exposure questions come before the grade

Most wrong-grade orders are not hardness errors. They are site descriptions that were never written down. Answer three questions before comparing compounds.

What is on the floor? Smooth sealed epoxy and polished tile ask for a blade that conforms and wipes cleanly. Broom-finished concrete, expansion joints, grit tracked in from a yard, and oily or greasy residues ask for a lip that resists abrasion and cutting. The same machine can move between both in one shift, which is worth stating on the order.

What chemistry and what temperature? Name the detergent, degreaser or solvent, and the wash-water temperature. A compound selected for abrasion resistance alone can swell or harden under a solvent it was never chosen for, and hot wash water changes how a lip behaves as much as cold ambient air does. If the cleaning programme changes, the compound decision re-opens even though the machine is identical.

How fast is a wet floor caught? On a rider covering a large area, a blade that loses its edge leaves a wide wet trail rather than a narrow one. OSHA 1910.22 is the US reference for keeping walking surfaces in a safe condition, which is why a missed seal is a facilities issue and not only a parts issue.

These three answers, not the hardness figure on a datasheet, decide which grade belongs on the machine. They are also the context worth putting on the purchase order, so a reorder six months later is the same specification rather than a fresh guess.

Map the answer to one of three grades

Hardness should be specified as a range with a tolerance and a named test method, not a single number. Durometer is measured by ASTM D2240, and classification and batch-to-batch consistency are framed by ASTM D2000. Ask for readings off production pieces rather than a compounder’s test coupon. Our three grades all carry a ±5 Shore A tolerance:

  • Natural rubber, 65 ± 5 Shore A — smooth tile, PVC and sealed epoxy. It conforms well to flat floors and gives the cleanest pickup on indoor commercial work. This is the default for most sites.
  • Cast polyurethane, 85 ± 5 Shore A — rough or damaged concrete, expansion joints, oily and greasy surfaces, and long shifts over abrasive floors. It generally lasts longest there.
  • Economy gum rubber, 45 ± 5 Shore A — light duty on smooth floors where the decision is price-led and the area is small.

Polyurethane is more sensitive to temperature and operating conditions than natural rubber. It is a specialist choice for named rough or oily accounts, not a flat upgrade for every site: a cold, unheated bay or a hot wash can take the edge off its advantage. That caveat is the single most useful sentence to put in front of a buyer who assumes harder is always better. Service life in normal commercial duty is typically two to three months, an industry figure rather than a guarantee; it moves with cleaning frequency, chemicals, temperature and floor condition.

The full trade-off, including where each grade stops making sense, is set out in our material comparison. Colour is not a specification either: red is pigment, performance is formulation, which is why our red rubber sheet guide treats the two separately. Our replacement cycle guide shows how to turn that interval into a reorder point from the number of units your customers run.

Count cost per shift, not price per strip

A cheap blade that is wrong for the site is replaced early, and each change costs labour, a machine out of service and a re-clean of the area it left wet. Price per strip is a small line in that sum. The useful comparison is the cost of a shift of dry floors, which folds together blade cost, changeover time and the downtime attached to a failed seal. On a rider the downtime term dominates.

The commercial terms are fixed and worth designing the trial around:

  • MOQ 20 sets per style on a profile we already tool.
  • USD 60–120 tooling for a new style, waived once cumulative volume reaches 500 sets.
  • Mixed orders allowed, with a USD 3,000 minimum order value, so one shipment can test several grades or several models instead of committing the budget to one.

Cumulative volume counts across reorders, so a stable profile moves toward the tooling threshold rather than restarting it. Samples are chargeable, not free, and take 7–15 days to prepare and ship; a profile we do not already tool adds a cutting step. Budget that window before the current set is due, not after the first streak appears. Consolidating styles into fewer, larger orders is standard practice in the cleaning channel, and ISSA material is a useful reference when making that case internally. The margin on this line usually sits in the gap against a captive OEM parts channel rather than in shaving unit price, an argument developed in OEM vs aftermarket squeegee blades.

Receiving: the seven-day window starts at the door

Claims are agreed on the order, not after it. The window is 7 days from receipt, counted from the delivery date rather than dispatch; only the defective pieces are replaced, not the whole batch; an unboxing video filmed from before the carton opens is required; and freight on replacement pieces falls to the buyer, which most importers absorb by consolidating into the next shipment.

Open cartons against your labelled sample ID, check the front and rear split, and compare the profile before fitting. Coverage is for manufacturing defects — damaged edges, wrong dimensions, hardness outside the agreed range — not ordinary wear, fitting damage, or a compound that was wrong for the floor. Ask for carton labelling by style and by half of the set; on a mixed order it is the cheapest insurance available.

Get a quote or a sample set

Send a worn front and rear blade or clear photos, a view of the assembly showing whether it is straight or curved, the floor and chemical context, the wash-water temperature, your fleet size, and your own sample ID. We will confirm the profile against your sample or drawing, say whether we already hold tooling, recommend a grade for the exposure window you described, and quote a 20-set trial. Request pricing or a sample set and we will come back with lead time and freight options.

Choose the compound for the site the machine actually works in. The hardness figure is the last thing to settle, not the first.

Facebook
LinkedIn
Twitter

Leave a Reply

Your email address will not be published. Required fields are marked *

19 + four =

Sign up and get

5% Off

On all squeegee blade

Ask For A Quick Quote

We will contact you within 1 working day, please pay attention to the email with the suffix “@ntheron.com”.