Tennant 5400 Squeegee Blades: Specs for Wholesale Buyers

Tennant 5400 Squeegee Blades

Table of Contents

Aftermarket replacement part — not a genuine OEM part. The squeegee blades and rubber parts on this page are aftermarket replacements made to fit Tennant machines. They are not genuine Tennant parts, we are not affiliated with or endorsed by Tennant, and brand names, model names and part numbers are used for fitment reference only. Confirm dimensions against your own sample or drawing before ordering.

The most important line on a squeegee blade specification is the one you can only use after the carton has already arrived. Most spec sheets describe a blade nobody can check at the goods-in door. For a wholesale buyer stocking blades for the Tennant 5400, a useful specification is not a list of dimensions but a short set of pass-or-fail gates that a receiving clerk, a phone camera and a durometer can enforce. This page sets out those gates, the three compounds behind them, and the terms that decide what happens when a shipment disagrees with the order.

A model name is not a specification

“Tennant 5400” identifies a machine family. It does not define slot width, lip geometry, thickness, hole pitch or overall length, and we do not publish dimensions, OEM part numbers or abrasion test values that we cannot confirm from your sample or drawing. A tidy figure that seats the lip at the wrong angle leaves a trail on the floor and is then reported as a bad batch of rubber. Where a dimension is missing, confirm it with us against your own sample or drawing rather than filling the gap with a catalogue number.

The Tennant official site is the right place to start for machine documentation, though it will not tell you which aftermarket profile fits a frame that was revised or replaced in service. Our cross-reference guide lists the profiles we already hold tooling for; treat it as a starting list, then confirm against the worn blade. A frame swapped for a non-original assembly, an earlier production run with a revised frame, or a set trimmed and re-drilled on site each count as a new profile, whatever the badge says.

One distinction belongs at the top of every enquiry: one set is one front blade plus one rear blade. On a wide machine the rear carries the vacuum seal across the width, while the front takes the debris and most of the abrasion. A request that says only “5400 blades” is routinely priced as single strips, so state the split before anyone quotes.

Gate one: the carton disagrees with the order

The first check is administrative and it catches more disputes than any laboratory test. Open cartons against the purchase order and the labelled sample ID, count front and rear pieces separately, and check that the carton label names the style and the half of the set. Ask for carton labelling by style and by half of the set when you order; on a mixed shipment it is the cheapest insurance available, and it turns a receiving check into a ten-minute job rather than a reconciliation exercise.

Photograph the unopened carton, the label, and the first layer of blades before fitting anything. The claims window is short, and the evidence that decides a claim is created in those first few minutes. A spec naming a sample ID, a set split and a carton label is already more enforceable than one naming a hardness figure alone.

Gate two: the blade disagrees with the sample

Keep a retained sample — a worn front and rear blade from the machine you are buying for, tagged with your own sample ID. Lay the delivered pieces against it. Check the profile, the length and the hole positions against the sample or drawing, and look at the assembly view that shows whether the frame is straight or curved. If the frame was replaced in service, the sample is the specification and the model name is only a cross-reference.

Hardness is the other half of this gate. Specify it as a range with a tolerance and a named test method, not a single number. Durometer is measured by ASTM D2240, and classification and batch-to-batch consistency are framed by ASTM D2000. Ask for readings off production pieces rather than a compounder’s test coupon. Our three grades all carry a ±5 Shore A tolerance:

  • Natural rubber, 65 ± 5 Shore A — smooth tile, PVC and sealed epoxy. It conforms well to flat floors and gives the cleanest pickup on indoor commercial work. This is the default for most sites.
  • Cast polyurethane, 85 ± 5 Shore A — rough or damaged concrete, expansion joints, oily and greasy surfaces, and long shifts over abrasive floors. It generally lasts longest there.
  • Economy gum rubber, 45 ± 5 Shore A — light duty on smooth floors where the decision is price-led and the area is small.

Polyurethane is more sensitive to temperature and operating conditions than natural rubber. It is a specialist choice for named rough or oily accounts, not a flat upgrade for every site: a cold, unheated bay or a hot wash can take the edge off its advantage. Service life in normal commercial duty is typically two to three months, an industry figure rather than a guarantee; it moves with cleaning frequency, chemicals, temperature and floor condition. The full trade-off, including where each grade stops making sense, is set out in our material comparison. Colour is not a specification either: red is pigment, performance is formulation, which is why our red rubber sheet guide treats the two separately.

A grade that was right for the site six months ago may be wrong now if the floor, the detergent or the wash-water temperature changed. Our replacement cycle guide shows how to turn that interval into a reorder point from the number of units your customers run, so a reorder is a repeat of a known specification rather than a fresh guess.

Gate three: the terms disagree with the quote

The third gate is commercial, and it belongs on the specification because it decides whether a failed check has a remedy. The fixed terms are worth designing the trial around:

  • MOQ 20 sets per style on a profile we already tool.
  • USD 60–120 tooling for a new style, waived once cumulative volume reaches 500 sets.
  • Mixed orders allowed, with a USD 3,000 minimum order value, so one shipment can test several grades or several models instead of committing the budget to one.

Cumulative volume counts across reorders, so a stable profile moves toward the tooling threshold rather than restarting it. Samples are chargeable, not free, and take 7–15 days to prepare and ship; a profile we do not already tool adds a cutting step. Budget that window before the current set is due, not after the first streak appears. Consolidating styles into fewer, larger orders is standard practice in the cleaning channel, and ISSA material is a useful reference when making that case internally. The margin on this line usually sits in the gap against a captive OEM parts channel rather than in shaving unit price, an argument developed in OEM vs aftermarket squeegee blades.

The claims window starts at the door, not at the factory

Claims are agreed on the order, not after it. The window is 7 days from receipt, counted from the delivery date rather than dispatch; only the defective pieces are replaced, not the whole batch; an unboxing video filmed from before the carton opens is required; and freight on replacement pieces falls to the buyer, which most importers absorb by consolidating into the next shipment. Coverage is for manufacturing defects — damaged edges, wrong dimensions, hardness outside the agreed range — not ordinary wear, fitting damage, or a compound that was wrong for the floor.

The three gates line up with that policy: the carton check produces the unboxing video, the sample check produces evidence of an out-of-range dimension or durometer reading, and the terms check defines “defective”. A buyer who writes all three into the specification spends the seven days documenting a decision; one who writes none spends them negotiating one. A wet floor is a facilities issue, not only a parts issue — OSHA 1910.22 is the US reference for keeping walking surfaces safe, which is why the cost of a late or wrong replacement lands well beyond the price of the rubber.

Get a quote or a sample set

Send a worn front and rear blade or clear photos, a view of the assembly showing whether it is straight or curved, the floor and chemical context, the wash-water temperature, your fleet size, and your own sample ID. We will confirm the profile against your sample or drawing, say whether we already hold tooling, recommend a grade for the exposure you described, and quote a 20-set trial. Request pricing or a sample set and we will come back with lead time and freight options.

Write the specification for the person who opens the carton. If they cannot fail a shipment with it, it is not a specification yet.

Facebook
LinkedIn
Twitter

Leave a Reply

Your email address will not be published. Required fields are marked *

eight − 1 =

Sign up and get

5% Off

On all squeegee blade

Ask For A Quick Quote

We will contact you within 1 working day, please pay attention to the email with the suffix “@ntheron.com”.